chinesetaya.blogg.se - Quasar laser

#Quasar laser how to#
#Quasar laser serial#
#Quasar laser drivers#
#Quasar laser 32 bit#

Ophir provides example projects of COM Object clients in VC#, VB.NET and LabVIEW.Standard USB cable (P/N 7E01202) for use with the Pulsar devices (included).

#Quasar laser how to#

OphirLMMeasurement COM Object.pdf describes how to register it on another PC where the Ophir application has not been installed.

The COM object is registered when the application is installed. COM object component developed and supplied by Ophir for communication with the Juno, Juno+, Nova-II, Pulsar, USBI, Vega, Centauri, StarBright and StarLite devices.

OphirLMMeasurement COM Object.pdf lists and describes the methods and events available for configuring, controlling and uploading measurements from Ophir devices.

System Integrators will need the following components: These components are installed as part of the StarLab application’s installation process.

#Quasar laser drivers#

OphirLMMeasurement is a COM Object that is included as part of the StarLab installation (StarLab 2.10 and higher) that allows the system integrator to take control of the Juno, Juno+, Nova-II, Pulsar and Vega, Centauri, StarBright and StarLite devices integrating them into his in-house measurement and analysis package.įor communication via USB, device drivers and additional support software must be installed on your PC. Ophir provides a common interface for communication and control of all of our USB speaking devices. This allows system integrators to leverage Ophir’s excellence in measurement capabilities with legacy analysis packages. Again, press "next" (install software automatically)įrom here on you may apply LabVIEW VI's on your deviceīesides their use as stand-alone, fully featured laser power/energy meters, Ophir devices are easily incorporated into larger end-user applications.

Select "not this time" & press "next" button.

Reconnect the Ophir Juno device to the PC that you wish to apply LabVIEW VI's on If asked by Wizard (i.e.

Press "OK" again (after SwapINF is done).

Press "OK" (you have already removed these).

Press "Swap" button - You will be prompted to "Remove the Ophir Juno Devices before continuing".

Disconnect any Juno OPHIR Device from the PC.

The sequence for preparing to interface the Ophir Juno (or meters connected through USB) with LabVIEW is generally as follows: If writing your own LabVIEW application, make sure that the OphirLMMeasurement COM Object is included in your LabVIEW applicationįor customers using the legacy OphInstr LabVIEW package, here are additional clarification steps to assist establishing the interface to LabVIEW when connecting an Ophir meter such as the Juno/USBI/Nova II/Vega with the USB. įor customers using the new LabVIEW COM Demo, there is nothing additional to do. More information, and software download, is available at.

In addition to all basic measurement and data logging functions, it also offers a wide range of special functions (including user-defined mathematical functions), multi-channel operation, COM Object for integration with external systems, etc. StarLab is our full-featured PC application that connects via USB to all Ophir USB-speaking instruments (Centauri, StarBright, StarLite, Vega and Nova II meters, as well as Juno, Juno+, EA-1, Pulsar and the Bluetooth-enabled Quasar PC interfaces). More information, including software download, is available at.

#Quasar laser 32 bit#

StarCom should nevertheless be able to work on a Win7 32 bit PC. The last release of StarCom was in 2008, with all that this implies.

#Quasar laser serial#

For a relatively new computer, you'd have to check that it has a serial port to which to connect the meter. It performs all basic functions such as real-time data logging, saving data in PC file, off-line data viewing, printing, etc. StarCom is our legacy PC application which connects via RS232 (not USB), for old Ophir instruments having RS232 interface capability (Vega, Nova II, LaserStar and Nova).